DIN125 Flat Washer: Load Risks of Stacked Washers
You are here: Home » News » Industry News » DIN125 Flat Washer: Load Risks of Stacked Washers

DIN125 Flat Washer: Load Risks of Stacked Washers

Views: 0     Author: TOPBOLT technical team     Publish Time: 2026-11-19      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button

1 Common Misconceptions of Stacked Washers

1.1 Wrong operation for surface leveling

When facing gaps or uneven contact surfaces, many installers stack multiple DIN125 flat washers for leveling. They believe stacked thin washers perform the same as one thick washer. This shortcut shows no obvious failure in light static load for a short time, yet it creates severe hidden risks for high-strength joints such as steel structures, equipment frames and flange connections.

1.2 Slip between stacked interfaces

Every contact surface between two washers is an independent friction plane. More stacked washers mean more slip planes. During tightening, washers tend to shift and tilt, creating eccentric load instead of pure axial clamping force.

2 Failure Modes Caused by Stacked Washers

2.1 Washer crushing from uneven load

The bearing area and hardness of DIN125 flat washers are designed for single-piece installation. When stacked, pressure cannot be evenly distributed. Local overpressure causes plastic collapse of washers. Once crushed, bolt preload drops rapidly and the joint loosens.

2.2 Preload loss and joint failure

Under vibration and temperature cycling, tiny slip and embedment relaxation happen between stacked washers, leading to continuous preload decay. For high-strength friction connections that require stable preload, insufficient clamping force will result in joint slip and seal failure.

2.3 Non-compliance with site inspection standards

Inspectors for overseas steel structure, piping and machinery projects usually reject gap compensation by stacking multiple standard flat washers. This practice violates fastening assembly specifications and leads to rework and project delay.

3 Comparison: Single Washer vs Stacked Washers

Item

Single DIN125 Flat Washer

Stacked DIN125 Washers

Load condition

Uniform load, stable contact surface

Eccentric load, easy slip between washers

Preload stability

Consistent preload retention

Gradual preload loss over time

Application

Most standard bolted joints

Only temporary light static assembly; forbidden for high-strength connections

Recommended alternative

Thick flat washer, custom spacer, shim set

Not recommended for permanent structural joints

4 Correct Solutions for Gap Compensation

4.1 Use thick flat washers of matching size

When gap adjustment is required, replace stacked standard DIN125 washers with a single thick washer of identical material and hardness, to maintain only one bearing interface.

4.2 Use machined spacers or shim sets for large gaps

For larger gaps, adopt machined spacers or precision shim packs. These parts feature controlled parallelism and avoid slip risks of stacked thin washers.

4.3 Correct workpiece contact surface at source

Uneven surfaces or hole misalignment should be fixed by reworking the workpiece instead of relying on washers for compensation. This is the most reliable engineering method.

5 Checklist for Sourcing and On-site Assembly

  1. For high-strength bolts, vibration service and flange sealing joints: only one DIN125 flat washer per bearing side

  2. Check drawings before assembly. Do not stack washers for gap adjustment without design approval

  3. Inspect bolt head and nut areas for unauthorized stacked washers during site audit

  4. Inform customers of load risks in advance if they insist on stacking washers, and update the technical solution

FAQ

Q1: Can two stacked DIN125 washers work safely for a short period? A1: It may hold temporarily under light static load without vibration, but long-term reliability cannot be guaranteed. The risk of loosening rises sharply under vibration and cyclic load.

Q2: Can stacking be safe if DIN125 washers have high hardness? A2: Adequate hardness cannot eliminate the risk. The main hazard comes from eccentric load and slip at multiple interfaces, which still causes local stress concentration and crushing.

Quick Links

Fasteners

Contact Us

WhatsApp: +1 5419089592
Phone: +86 15825577288
Email: sales2@topboltmfg.com
Address: tongtu Road, Yinzhou District, Ningbo, China

Join Our Newsletter

Promotions, new products and sales. Directly to your inbox.
Copyright ©  2024 Ningbo Topbolt Metalworks Co., Ltd. All Rights Reserved. Sitemap. Privacy Policy